MP2100B Anritsu BERTWave™ (10G BERT, sampling oscilloscope)
With the popularity of cloud computing, the demand for optical modules in data centers is increasing day by day. In particular, the demand for SFP+ modules (for dry 10GbE) and OSFP+ modules (40GbE (10Gbit/sx4)) is growing rapidly. The all-in-one BERTWaveMP2100B has a built-in BERT tester and sampling oscilloscope to run both BER tests and eye diagram analysis required for developing and manufacturing modules. the number of BERT channels can be expanded to four and supports 4-channel simultaneous BER measurements. In addition, the high sampling speed reduces the measurement time of the eye diagram. The MP2100B can be used to measure multi-channel optical modules such as OSFP+ more efficiently.
Model: MP2100B
Name: All-in-one BER eye diagrammer
Brand: Anritsu
Category: General electronic test > oscilloscope > BER eye diagrammer all-in-one machine
Product attributes: host
Features
All-in-one built-in 4-channel BERT and sampling oscilloscope
Bit Error Rate (BER) 4-channel simultaneous measurement
High quality waveform PPG (1 ps rms jitter)
High input sensitivity (10 mVp-p minimum input sensitivity)
High-speed eye diagram template test up to 150 k samples/sec with eye diagram analysis
Supports differential signal BER measurements, eye diagram template testing and eye diagram analysis
Choice of up to six Bessel filters for full-featured application support
Compact (18 cm deep) optical module evaluation tester
Simultaneous bit-error-rate (BER), eye diagram, eye diagram template and jitter measurements in one unit
Supports WDP (waveform dispersion loss) measurements
Supports optimal sampling calculations for testing eye diagrams in both weighted and balanced conditions
Simulates simultaneous eye diagram patterns, eye diagram templates and jitter measurements of waveforms
All-in-one 4-channel BER measurement and eye diagram analysis Increasing the number of channels significantly reduces the measurement time of the QFSP+ module. If the number of channels is not increased, the measurement time will be relatively long.
The integrated sampling oscilloscope with integrated BERT simplifies measurement system configuration and control to support simultaneous BER measurements and EYE mode analysis, reducing measurement time by approximately 40% compared to combining separate instruments. In addition, BERTS can be extended to 4" to support simultaneous error measurements on all QSFP+ module channels, which can further reduce measurement time by 70% since time-consuming channel switching operations have been eliminated.
Flexible Measurement System Configuration Traditional measurement systems using BERT as a signal source and a separate sampling oscilloscope to perform eye diagram analysis are more complex. MP2100B integrates BERT and sampling oscilloscope into the same unit to provide an easy to configure measurement system.
The BERTWave MP2100B is an all-in-one tester with built-in BERT and sampling oscilloscope for supporting optical module evaluation, including BER measurements, eye diagram template testing, and eye diagram analysis.
BERT and sampling oscilloscopes are necessary testers when evaluating optical modules used in optical communication systems. Previously, when evaluating modules such as QSFP+ and SFP+, separate BERTs and sampling oscilloscopes were required. Now with the BERTWave MP2100B, its all-in-one design integrates up to four channels of BERT and sampling oscilloscopes into a single compact 18-cm deep cabinet, significantly cutting equipment investment costs and saving operating space. In addition, when using the BERTWave MP2100B, BER measurements, eye diagram template tests and eye diagram analysis can be performed simultaneously without changing connection lines, thus reducing measurement time. Moreover, BER measurement channels can be expanded to four, and 4-channel BER measurement, eye diagram template test and eye diagram analysis can be performed simultaneously. Finally, the built-in SFP+ module slot eliminates the need for an external light source.
The BERTWave MP2100B's BERT measures bit-error-rate (BER) at bit rates between 125 Mbit/s and 12.5 Gbit/s, and its built-in BERT option for up to four channels makes it easy to configure multi-channel optical module test systems such as QSFP+ and AOC. The differential signal supports not only BER measurements, but also eye diagram template testing and eye diagram analysis.
The sampling oscilloscope BERTWave MP2100B has an electrical interface with a bandwidth of 25 GHz (typical) and an optical interface with a bandwidth of 9 GHz (typical). In addition, with this oscilloscope, up to six optical Bessel filters can be built in for measuring optical signals. Using these filters, one MP2100B enables extinction ratio measurements, eye diagram template testing and eye diagram analysis for a variety of different applications. In addition, the oscilloscope features a fast sampling mode as standard to ensure high-speed measurements; in fast sampling mode, the sampling speed is up to 150k samples/second, 1.5 times faster than older models, and enables fast eye-diagram template testing and eye-diagram analysis.
With the MX210001A jitter analysis software, one unit enables simultaneous jitter analysis, eye diagram and eye diagram template measurements. 150k samples/second sampling speed also makes more efficient use of measurement time. Used in conjunction with MATLAB®, it can be used to support waveform dispersion measurements for specific signals such as WDP, TWDP, and dWDP.
Finally, the MX210002A transmission analysis software adds device transmission (S21 gain, phase) analysis, as well as inverse embedded waveform simulation performed using equalizers, filters, and weighting calculations. Simultaneous waveform sampling and simulation, as well as simultaneous eye diagram measurements and eye diagram template measurements, are also supported. Simulated waveform synchronous jitter measurements can also be performed in conjunction with the MX210001A software.
With the popularity of cloud computing, the demand for optical modules in data centers is increasing day by day. In particular, the demand for SFP+ modules (for dry 10GbE) and OSFP+ modules (40GbE (10Gbit/sx4)) is growing rapidly. The all-in-one BERTWaveMP2100B has a built-in BERT tester and sampling oscilloscope to run both BER tests and eye diagram analysis required for developing and manufacturing modules. the number of BERT channels can be expanded to four and supports 4-channel simultaneous BER measurements. In addition, the high sampling speed reduces the measurement time of the eye diagram. The MP2100B can be used to measure multi-channel optical modules such as OSFP+ more efficiently.
Model: MP2100B
Name: All-in-one BER eye diagrammer
Brand: Anritsu
Category: General electronic test > oscilloscope > BER eye diagrammer all-in-one machine
Product attributes: host
Features
All-in-one built-in 4-channel BERT and sampling oscilloscope
Bit Error Rate (BER) 4-channel simultaneous measurement
High quality waveform PPG (1 ps rms jitter)
High input sensitivity (10 mVp-p minimum input sensitivity)
High-speed eye diagram template test up to 150 k samples/sec with eye diagram analysis
Supports differential signal BER measurements, eye diagram template testing and eye diagram analysis
Choice of up to six Bessel filters for full-featured application support
Compact (18 cm deep) optical module evaluation tester
Simultaneous bit-error-rate (BER), eye diagram, eye diagram template and jitter measurements in one unit
Supports WDP (waveform dispersion loss) measurements
Supports optimal sampling calculations for testing eye diagrams in both weighted and balanced conditions
Simulates simultaneous eye diagram patterns, eye diagram templates and jitter measurements of waveforms
All-in-one 4-channel BER measurement and eye diagram analysis Increasing the number of channels significantly reduces the measurement time of the QFSP+ module. If the number of channels is not increased, the measurement time will be relatively long.
The integrated sampling oscilloscope with integrated BERT simplifies measurement system configuration and control to support simultaneous BER measurements and EYE mode analysis, reducing measurement time by approximately 40% compared to combining separate instruments. In addition, BERTS can be extended to 4" to support simultaneous error measurements on all QSFP+ module channels, which can further reduce measurement time by 70% since time-consuming channel switching operations have been eliminated.
Flexible Measurement System Configuration Traditional measurement systems using BERT as a signal source and a separate sampling oscilloscope to perform eye diagram analysis are more complex. MP2100B integrates BERT and sampling oscilloscope into the same unit to provide an easy to configure measurement system.
The BERTWave MP2100B is an all-in-one tester with built-in BERT and sampling oscilloscope for supporting optical module evaluation, including BER measurements, eye diagram template testing, and eye diagram analysis.
BERT and sampling oscilloscopes are necessary testers when evaluating optical modules used in optical communication systems. Previously, when evaluating modules such as QSFP+ and SFP+, separate BERTs and sampling oscilloscopes were required. Now with the BERTWave MP2100B, its all-in-one design integrates up to four channels of BERT and sampling oscilloscopes into a single compact 18-cm deep cabinet, significantly cutting equipment investment costs and saving operating space. In addition, when using the BERTWave MP2100B, BER measurements, eye diagram template tests and eye diagram analysis can be performed simultaneously without changing connection lines, thus reducing measurement time. Moreover, BER measurement channels can be expanded to four, and 4-channel BER measurement, eye diagram template test and eye diagram analysis can be performed simultaneously. Finally, the built-in SFP+ module slot eliminates the need for an external light source.
The BERTWave MP2100B's BERT measures bit-error-rate (BER) at bit rates between 125 Mbit/s and 12.5 Gbit/s, and its built-in BERT option for up to four channels makes it easy to configure multi-channel optical module test systems such as QSFP+ and AOC. The differential signal supports not only BER measurements, but also eye diagram template testing and eye diagram analysis.
The sampling oscilloscope BERTWave MP2100B has an electrical interface with a bandwidth of 25 GHz (typical) and an optical interface with a bandwidth of 9 GHz (typical). In addition, with this oscilloscope, up to six optical Bessel filters can be built in for measuring optical signals. Using these filters, one MP2100B enables extinction ratio measurements, eye diagram template testing and eye diagram analysis for a variety of different applications. In addition, the oscilloscope features a fast sampling mode as standard to ensure high-speed measurements; in fast sampling mode, the sampling speed is up to 150k samples/second, 1.5 times faster than older models, and enables fast eye-diagram template testing and eye-diagram analysis.
With the MX210001A jitter analysis software, one unit enables simultaneous jitter analysis, eye diagram and eye diagram template measurements. 150k samples/second sampling speed also makes more efficient use of measurement time. Used in conjunction with MATLAB®, it can be used to support waveform dispersion measurements for specific signals such as WDP, TWDP, and dWDP.
Finally, the MX210002A transmission analysis software adds device transmission (S21 gain, phase) analysis, as well as inverse embedded waveform simulation performed using equalizers, filters, and weighting calculations. Simultaneous waveform sampling and simulation, as well as simultaneous eye diagram measurements and eye diagram template measurements, are also supported. Simulated waveform synchronous jitter measurements can also be performed in conjunction with the MX210001A software.